Verilink 1558A (CG) Configuration/Installation Guide Manual do Utilizador descarregar pdf

TRANSPORT

1558A APS

Configuration Guide

Part Number 45-00083

Revision 2.0

1558A Front View

AUTO T1 PROTECTION SWITCH

SUPV PWR

STATUS

ABYPASS LOCKED B

ALM LOS LP

SELECT

AUTO

PATH

STATUS

PATH

RX BRDG

TX BRDG

RX BRDG

TX BRDG

DTE

LOS

RX BRDG

TX BRDG

TxPORT 1558A

-20 to -56 VDC, 200 MA

DTE COM BUSNET BNET A

IN OUT

GND

–VDC (A)

RTN (A)

–VDC (B)

RTN (B)

Alarm NO

Common

Alarm NC

S2 S3 S4

Switch S1

S1-7 S1-8 Boot from

Off

Off Switches

Off On Manager

On Off RAM

On On ROM

DTE to NET

Block FDL

NET to DTE

Block FDL

DTE to NET

Regen CRC

NET to DTE

Regen CRC

Card Function

Slave

ARM

from ROM

DTE to NET

Pass FDL

NET to DTE

Pass FDL

DTE to NET

Pass CRC

NET to DTE

Pass CRC

Card Function

Master

ARM

from RAM

12345678

Boot Mode

Off

12345678

Framing Errors

Enabled

LOS

Enabled

NET A

B8ZS

NET B

B8ZS

DTE

B8ZS

CSU Mode

Framing Errors

Disabled

LOS

Disabled

NET A

AMI

NET B

AMI

DTE

AMI

Path Revert

Disabled

DTE Framing

ESF

CSU Mode

Path Revert

Enabled

DTE Framing

Enabled

Disabled

Off

Switch S2

1558A Rear View

1558A Controls and Indicators

Index Indicator Description

1 SUPV The Supervisory port allows the user to connect to the 1558A via a PC running the supplied LAPS software.

2 Power One or both of these green LEDs will be ON when a nominal power source of -20 to -56 VDC is present on the PWR A and PWR B terminals.

3 Bypass This red LED indicates whether the unit is in a ‘bypass’ mode of operation (ON if the unit has detected a CPU watchdog operational fault and OFF

under normal operation.

4 Locked When the 1558A has been manually forced to either the A or B path, this amber LED is on. Moving the Path Select switch back to the AUTO

position turns off this LED and restores normal APS operation.

5 A / B These amber status LEDs indicate which of the two T1 receive paths (A or B) is presently being utilized

6 Path Select

Auto/A/B

The user can manually force and lock either the A or B path as the active path by moving this switch from the AUTO position to either the A or

B position. The 1558A is now manually locked to this path and will not switch from it, even if the selected path is or will be in a failed state.

7 Alarm These red LEDs indicate that the user definable alarm parameters (ES, CSES, LOS, and LOF) have been met or exceeded for Path A or Path B.

8 LOS This amber LED indicates that no T1 pulses are being detected on the receive signal paths from the network for Path A or Path B.

9 Loop This amber LED indicates that a loop has been activated for Path A or Path B.

10 Test Jacks Bantam test access jacks and bridge/monitor jacks are provided to gain physical access to the T1 path for NET A, NET B, and the T1 DTE path.

11 Loop/LOS The amber ‘Loop’ LED indicates that a loop has been activated on the DTE. The red ‘LOS’ LED indicates a loss of signal on the DTE.

NOTE: For future reference, all DIP switches

on this sheet are provided with boxes to check

according to the particular user selection. Facto-

ry default settings are shown underlined

Switches S3 and S4 are shown on the back side.

1 2 3 4 5 6 7 8 9 10 10 11 10

1 2

Resumo do Conteúdo

Página 1

TRANSPORT®1558A APSConfiguration GuidePart Number 45-00083Revision 2.01558A Front View AUTO T1 PROTECTION SWITCHASUPV PWRBSTATUSABYPASS LOCKED BABALM

Página 2 - Switch S4 Switch S3

1558A Block Diagram BNET-20 to 56 VDC/RTN(Power A)-20 to 56 VDC/RTN(Power B)PowerCOM BusDTERJ48RxTxRxSupply±12 VDC+5 VDCTxPowerLineDeframerNET AFramer

Comentários a estes Manuais

Sem comentários

Verilink 1558A (CG) Configuration/Installation Guide Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Hardware de computador Verilink 1558A (CG) Configuration/Installation Guide. Verilink 1558A (CG) Configuration/Installation Guide User Manual Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Hardware de computador Verilink 1558A (CG) Configuration/Installation Guide